塑料粉碎机的维护内容及方法

塑料粉碎机的维护内容及方法

1. 挡帘 Check apron

观察档帘是否有更替的必要，视情况自行判定。避免造成回收料污染。

Observe whether the check apron needs to be replaced and determine according to specific situations. Avoid recycled material pollution.

2. 安全装置 Safety equipment

1）启动粉碎机

Turn on the granulator

2）松动安全开关的星形把手，直至安全开关完全分离

Loosen the star shaped handle of the safety switch until it completely falls apart

3）如粉碎机及时停机，说明安全装置功能正常。

If the granulator stopped promptly, then the safety equipment functions properly.

注：如果安全开关分离后机器未能停机，请立刻手动停机（断掉主电源）并联系设备负责人。

Note: if it fails to shut down the machine by separating the safety switch, immediately perform manual shutdown (cut off the main power supply) and contact the person in charge.

3. 电器元件 Electric components

参照电器件连接部分，检查电器件所有线路是否松动脱落或损坏，有资格的工程人员可进行检查维修。

Refer to the electric Component Connection section, check all the circuit of electric components for loss or damage, qualified engineers can conduct inspection and maintenance.

4. 润滑 Lubrication

所有轴承均是终身免润滑的，不必加润滑油脂

All bearings are free of lubrication for lifetime, lubricating grease is not necessary.

5. 传送带 Conveyor belt

如果是带有传送带装置的设备，For equipment with conveyor belt

1）请检查传送带的方向是否正确

check if the direction of the conveyor belt is correct

2）检查输送带运动的直线度，如果皮带在运动过程中是倾斜的，先停止运转

如下图，打开端部盖板，调整调节螺丝C约1/4圈，再开机运转检查皮带的直线性，反复调节直到皮带运动的直线度满足要求不再倾斜。

Check the linear of belt movement, if it is oblique, then stop the equipment as shown in the following picture, repeat adjustment until the belt movement meet the requirements.

注：皮带的直线性公差在1%，调节螺丝的扭力不能超过5N.M

Note: the linear tolerance of belt is 1%, the torque force of regulating screw should not exceed 5N.M

6. 清洁 Cleaning

1）对于使用过程中粉尘容易产生情况下的清洁，每天或至少每周需要清洁一次，轴承部分每天都需要用吸尘器清洁粉尘；

In case that dust is easy to be generated in use, it needs to be cleaned every day or at least once a week, the bearing part needs to be cleaned with vacuum cleaner every day.

2）对于正常情况情况下的使用，每300小时需要需要清扫一次，轴承部分每周需要用吸尘器清洁一次。

For normal use, it needs to be cleaned every 300 hours, the bearing part needs to be cleaned with vacuum cleaner every week.

3）轴承处的清理：见下图，用洗尘器进风管口对准排屑槽，旋转转子几圈即可。

Cleaning the bearing part: as shown below, face the inlet nozzle of vacuum to the chip removal groove, spin the rotor for a few circles.

注：轴承处粉尘的清理非常重要，虽然奥为有充分的防尘结构，但难免有少量粉尘进入，在高温下容易造成轴承的损坏。

Note: Cleaning the dust in the bearing part is very important, although Aowei has complete dust-proof structure, but it is inevitable that a small amount of dust entering, which may cause damages to the bearing at high temperature.

7. 的动定刀 Rotating and fixed blades

1）切削室的所有动定刀螺丝螺母均带螺纹紧固剂，在任何情况下均不能私自松动、加固、更换。

All the screw nuts of rotating and fixed blades in the cutting chamber are equipped with threaded fastening agent, it cannot be loosened, reinforced or replaced without permission under any circumstances.

2）动定刀间隙要定期检查，正确的间隙应该在0.15-0.25;

切忌使用刃口钝化的刀片，这样不紧造成机器的磨损，也造成能耗的损耗，也不能得到高品质的回收塑料粒子，动刀片要根据情况及时更换，定刀也要根据情况及时修磨或更换。

The gap between rotating and fixed blades should be regularly checked, proper gap should be 0.15-0.25. Do not use blades with passivated cutting edge, it will not only cause abrasion and loss of energy, but also make it hard to get high quality recycled plastic particles, rotating blades should be replaced according to the situation, fixed blades should be repaired or replaced as needed.

3）在更换刀片的情况下，所有螺丝必须废弃掉，必须更换新的12.9级高强度螺丝，所有垫片，动定刀压块必须使用奥为生产或认可的部件。

When replacing blades, all the screws should be abandoned and replaced by 12.9 grade High-strength screws, all pads and briquetting of rotating and fixed blades should use parts produced or approved by Aowei.

处理刀片的时候需要小心，它们很锋利，可能造成人身伤害。更换刀片的时候请戴上防护手套，以免割伤手指或手。

Be careful when dealing with the blades, they are sharp and may cause personal injury. Wear protective gloves when replacing blades so that they won’t cut your fingers or hands.

4）转子本身容易转动，在更换刀片时候必须有木头块放置在切削中防止转子转动。

Rotator can be easily rotated, when replacing blades, place wood blocks in the cutting chamber to prevent the rotator from moving.

8. 驱动皮带 Driving belt

1)手动旋转皮带轮几圈，检查皮带是否有裂口缝隙或边缘磨损，齿牙是否有破裂

Manually rotate the belt pulley for a few times to check whether there are cracks, gaps or edge abrasion on the belt, whether there are cracks on the teeth

2）在更换皮带或皮带轮的时候，务必调整皮带轮与电机驱动轮的平行度，保持皮带张力适中，皮带张力大小根据皮带规格有关。检测皮带张力可使用张力计测定。

When replacing the belt or belt pulley, adjust the depth of parallelism between the belt pulley and the driving wheel to ensure that the belt tension is moderate, the belt tension is relevant to the belt specification. Tensiometer can be used to measure the belt tension.

9. 常见异常解决 Resolutions for commonly occurred abnormalities

问题描述

Problem deion

可能的原因

Possible causes

解决办法

Solutions

粉碎机或任何可选附件不能正常开启

Abnormal startup of granulator or other optional parts

急停开关未复位

Emergency stop switch fails to reset

将急停开关复位，按下急停开关，让急停开关弹起

Reset the emergency stop switch, press the emergency stop switch and allow it to bounce

粉碎机或选用附件未连接到主电源

Granulator or optional parts are not connected to the main power source

参见电器件的连接部分

Refer to the electrical equipment connection section

粉碎机电机的过载保护已跳起，

The overload protection of granulator bounces,

或者：

Or:

风机（可选）的过载保护跳起，或者：

The overload protection of fan (optional) bounces, or:

传送带（可选）的过载保护已跳起

The overload protection of conveyor belt (optional) bounces

重新复位所有热继的过载保护，并且在开机前：

Rest all the overload protection, and do before startup:

清理切削室及料仓风机部分

1) Clean cutting chamber and feed bin fan

调整皮带张力

2) Adjust the belt tension

调整动定刀间隙

3) Adjust the gaps between rotating blades

筛网架/料筒部分的安全开关未能锁紧

Safety switches of screen frame/charging barrel are not tightly screwed

打开料筒及筛网架检查所有星型把手及安全开关是否安装到位并锁紧

Open the charging barrel and screen frame to check if all the star-shaped handle and safety switches are correctly installed and locked

料位（可选）开关跳掉或者料位开关线路松掉

Material level (optional) switch jumps out or level switch line is loose

检查料仓料位或者：
连接料位电源线
check the material level in feed bin or connect the level power line

转子依然转动当料筒打开后

Rotator still operates after opening the charging barrel

皮带变形或皮带张力不正确；或者：

安全开关不能正常工作

Belt deformation or the belt tension is incorrect; or:

Safety switch is not working

更换皮带或者调整皮带张力，或者：

检查安全开关功能

Replace belt or adjust belt tension, or:

Check the function of safety switch

粉碎机或可选附件仍然不能工作在上述检查后

Granulator or optional parts do not work after the above inspection

停机

联系销售代理办

或联系奥为总部

1) Switch off

2)Press the emergency stop switch

3)contact sales agent

4)or contact the headquarter of Aowei

图片实拍

塑料粉碎机的维护内容及方法

塑料粉碎机的维护内容及方法

塑料粉碎机的维护内容及方法

塑料粉碎机的维护内容及方法

服务保障

作为国内大型的矿山设备生产厂家，旗下产出的设备型号有很多，因不同型号设备对应的产值大小，成本预算等并不是完全一样的，如您想了解具体的价格，欢迎随时客服，这里有专人实时在线为您详细解答。